Yes, another frame slider installation thread. These sliders were installed on a 2005 600RR using OES 2” radius cut frame sliders (). The pictures of the hardware were provided by Sodamninsane who initially encouraged me to install my own.

You will need the standard set of wrenches and tools but I highly recommend buying a Torque wrench to prevent over tightening of the engine bolts. CBR600RR OES Frame Slider Installation Instructions Part I: Cutting the holes Remove the right side mid fairing, disconnecting it from the lower and upper cowl. Place the alignment tool into the hexagonal shaped right engine bolt head. The sharp point of the alignment tool should be facing outward and the tool should have no lateral movement.

With the alignment tool in place, re-attach the fairing to the bike using at least three of the body screws. (Important) Make certain that the fairing is securely and precisely attached to the bike.

Press firmly on the fairing in the area of the tool to achieve a mark on the inside of the fairing. This mark will be the center of the new frame slider hole. Remove the fairing again. Drill a small hole through the tool mark from the back side out. At this point it is advisable to place the fairing back on the bike to insure the pilot hole is center with the motor mount bolt head.

Jun 18, 2013 Get these No-Cut Frame Sliders here: CycleCruza installs No-Cut Frame Sliders on his 2008 Honda CBR600rr. CBR1000RR 2004-05 NO CUT Frame Sliders Installation. Installation Instructions. CBR1000RR 2006-07 NO CUT Frame Sliders; CBR F4i 2004-06 Undertail. Hi Unregistered, the PSB Server is beginning to receive a lot of bounceback's and undeliverable emails associated with thread updates/subscriptions, personal message. Honda F4 & F4i frame sliders and bar ends from OES Accessories offer maximum protection and the. Fairing modification is required to install the frame sliders.

If you see that the tool tip is perfectly centered though the small hole, you are ready to cut the hole in your fairing for the slider. Select a hole saw that is ¼” bigger in diameter than the size of the slider and has a small pilot drill bit in it. I went with a 2” hole saw from Home Depot. Tape the entire area around the pinhole with blue painters tape to keep the cut clean. Begin the cut by placing the tip of the drill bit on the tiny pilot hole that you made and drill slowly through the plastic. Remember heat causes plastic to melt so take it slow.

The procedure for cutting the hole in the left fairing is the same except for one point: The motor mount screw must be broken loose and backed out enough for the tool to make contact with the inside of the fairing. Pcsx2 Plugins Gsdx 890 Google. The tool will be placed in the hole that goes thru the center of the bolt. Part II: Installing the sliders Start with the right side. Remove the factory nut on the backside of the motor mount bolt using the closed end of a 17mm wrench. Loosen the pinch bolt on the frame and push the engine bolt (threaded allen bolt) out of the hole. If the bolt does not slide out easily it may be necessary to support the engine with a hydraulic jack. Fisher Boy Game on this page. Place the jack under the oil pan using a piece of wood or rubber mat between the jack and the oil pan.

An aluminum spacer which lies between the engine and frame could fall out of place. Be sure not omit this spacer when installing the right slider. The engine bolt will be replaced with the new frame slider bolt and aluminum sleeve. The aluminum sleeve will be placed inside the frame above the pinch bolt. The shorter slider of the set goes on the right side of the bike. It includes an aluminum sleeve. The new frame slider bolt and aluminum sleeve will replace the right side engine bolt.

In this order, place the aluminum sleeve inside the frame above the pinch bolt. Place the Frame slider bolt thru the washer and then thru the right side frame slider. Continue pushing the bolt thru the aluminum sleeve and original aluminum spacer until the you see the bolt appear on the right side of the motor mount hole. External Dvd Drive Software more. Thread the original factory nut back on the new frame slider bolt and firmly tighten it down using a ratchet to keep the frame slider bolt from turning.